Restore your Holosun EPS Carry Red Dot Sight

Occasionally, you may require to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be performed in just a few actions.

Begin by ensuring your red dot sight is powered on.
Locate the small button for reset on the side of the device.
Use a small object to press and hold the reset button for approximately 5 seconds.
Disengage the reset button and your Holosun EPS Carry Red Dot sight will reboot.
The red dot sight should now be reverted to its factory settings.

Return to Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it to its factory configuration is a breeze. First, determine the tiny button on the rear of your optic. Then, press and hold it for around twelve seconds until you see a brief flash. Your Holosun EPS Carry is now reset to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

Press and hold the power button for approximately 10 seconds.
A message will flash, indicating that the reset is in progress.
Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and verify your sight's functionality. If you encounter any further difficulties, don't hesitate to contactsupport team.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

Beginning with, Turn on your Holosun EPS Carry by pressing the power button.
Next, press and hold both the mode button and the up/down adjustment button simultaneously.
During continue holding these buttons, activate the power button once.
You will show a confirmation prompt indicating that the reset process is initiated.
Allow the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reset your Holosun EPS Carry via a Factory Default Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the fix. This will restore your sight to its original settings, clearing any personalized configurations you've made. To execute this reset, follow these easy steps:

First, locate the reset lever on your EPS Carry.
Then, engage a fine object, like a pen tip, to push the reset button.
While hold the reset lever activated, activate your EPS Carry.
The sight will flash a message confirming that the reset is complete.

Once the reset is complete, check here your EPS Carry will be back to its factory settings.